#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR HOW TO#
#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR PDF#
#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR SERIAL#
#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR FULL#
#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR PLUS#

The shutter is a Synchro-Compur which was really just a Compur Rapid with M. It has an f/3.5 Xenar taking lens and an f/2.8 Heidosmat composing lens on top. Earlier Rollei-models 6 x 6 use Rolleikin I (with special back). (The combination back for two picture sizes was originally not provided with the first camera series, but could be ordered additionally). My Rolleiflex is the 3.5 Automat MX model. Rolleikin 3.5 and 2.8 Fits Rolleiflex 6 x 6 above numbers 1,100,000 and Rolleicord above numbers 1,137,000. To find out what model you have visit the Rollei Club website. Post pictures of it out of the camera and the sides with holes or similar. The box for the Rollei is also beautifully designed with ornate markings.

#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR HOW TO#

I do not know how to disassemble the view lens, likely set screws or pins in the barrel. The side plates have to be removed to access the wind and focus mechanisms. A fair amount of grease was used on the shaft and cams.

#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR PLUS#

Voir plus didГ©es sur le thГЁme appareil photo, appareil photo argentique, appareil photo ancien. The focus mechanism is a rod that goes through machined holes in the body, has two cams on each end with a spacer between them, and engage the arms which have a spring loaded guide at the rear. 2021 - DГ©couvrez le tableau 'ROLLEIFLEX' de LATOURP75 sur Pinterest. The wind mechanism is more complicated and operates best with NO oil or grease. How much of the light seal tube is accessible with the lens at infinity/fully retracted? You might be able to unscrew it and the rear cell if enough is gripable at infinity.

#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR PDF#

The shims are items 150 through 154 pdf page 155 and 155 L, M, N, P, Q depending on what was needed to get exact register and their positions are important. The lens carrier item 149 on pdf page 153 is attached to the focusing arms with 4 screws and has shims between the carrier and arms and cover frame item 158 pdf page 155.

#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR FULL#

If you have serviced Compur 00 shutters in the past then removing it from the camera and reinstalling it will be harder than a full tear down CLA on the shutter.

The shutter is a common Synchro Cmpur only modified with the face plate, aperture lever and shutter cocking lever changed. The complete lens/shutter assembly has to be removed to replace/repair that light block. The rear cell has a longish housing tube that slides through the light block as shown in post 38 photos. The front plate has to be removed to remove the shutter which requires resetting the parallex adjustment for the view mirror on reassembly.ДЄll Rollei I have serviced disassemble basically the same.ДЇirst off a Rollei does not have a bellows. The rear cell retaining ring will likely be on the shutter side of the cell barrel. Once the cells are removed from the shutter the retaining ring for the elements unscrew from the cell barrels and may be secured with a clear thread locker that dissolves with acetone. The front cell of the taking lens unscrews from the shutter and the rear cell should unscrew from the rear through the image box area (camera back opening). Infinity focus will have to be reestablished with the taking lens focused at the film plane on reassembly. Loosen the set screw for the view lens then unscrew the view lens from the front frame. To remove the front cover lift up the leatherette, remove it, then remove the 6 screws holding the face to the front frame. Remove the view hood and check the mirror as it can be the source of what you are seeing in the view lens. Use the 2.8E or 2.8F instructions as your guide.

#ROLLEIFLEX 2.8 ROLLEIKIN FLICKR SERIAL#

From serial 1.700.000 with a switch in the aperture wheel.Click to expand.All Rollei I have serviced disassemble basically the same.Дownload this service manual from my google drive:.

From serial 1.464.000 the EV coupling can be disengaged by pressing a button in the aperture wheel.

Main differences than Automat (MX) Model K4A:.

From serial 1.268.000 the camera accepts hand grip and quick mount plate.

Main differences than Automat (X sync.) Model K4/50:.

Shutter is Synchro-Compur.ДЄutomat (MX-EVS) model K4B image by Maria Cordell ( ImageВ rights) NOTE: my Automat s/n 1,207,277 has X-synch only, not MX.

The following parts of this model can be modernized: larger focusing knob & release safety lock.

Also useable after modifications: Rolleimarin I under water housing, Rolleimeter, Rolleiflash, Rolleikin 2 with dual format back.

The camera could be used with Rolleikin I to use 35mm film & with the special glass plate film adapter.

Backcover: hinged with exposure guide table, removable that can be exchanged for a dual film format back.

Winding: lever with auto stop, no red window, film pressure plate with black color coating.

Finder lens: Heidoscop Anastigmat 75mm f/2.8 filter Bayonet I.

Taking lenses: All with filter Bayonet I.

Film: 120 roll film, picture size 6ењ†cm & 35mm with Rolleikin I adapter set.

2 Later Automat models with flash sync.

Rolleiflex 2.8 rolleikin flickr